![]() Remember that the USB charging cable requires a high power (USB 2.0 or better) port. The CORSAIR HS80 MAX WIRELESS Headset battery has no “memory effect”, so there is no need to completely discharge it before recharging. Connect the USB charging cable to the CORSAIR HS80 MAX WIRELESS Headset.Connect the USB charging cable to any working USB port on your PC.The CORSAIR HS80 MAX WIRELESS Headset must be fully charged before its first use. In addition, pressing the volume wheel cycles through four audio EQ presets. Use the volume control/EQ select wheel to adjust volume up or down. A 30-degree bend is a good place to start, but you can adjust this if your mic is too loud or too soft. NOTE: iCUE software can also be used to control these features.įor best performance, bend the flexible microphone boom to best fit near the left corner of your mouth. The software’s built-in documentation explains how to use the HS80 MAX WIRELESS’s features in greater detail.įlip-up microphone to mute. Requires USB Wireless Receiver to enable. ![]() Enable SoundID ™ audio personalization.Select and customize audio equalizer (EQ) settings.After installation is complete, reboot your PC, and launch iCUE.Install the iCUE software on a PC running Windows 10 or later, or on macOS.NOTE: If the headset is used without software, some features will be disabled. The USB Wireless Receiver must be connected to your PC to use iCUE software. Using iCUE software will enable the full feature set of the HS80 MAX WIRELESS headset. Go to /support/downloads to download the iCUE Software. Take breaks between sessions and always begin with the volume at a low level before increasing. NOTE: Prolonged listening at high volumes may adversely affect your hearing. Keep the headset at room temperature (20–30☌ or 68–86☏).Battery life is maximized by keeping the battery in a partially charged state. Do not leave the battery fully discharged for long periods.Make sure the battery is fully charged before initial use.Place the wireless USB receiver in an open, unobstructed area.To skip backwards, press the MFB three times quickly. To skip forward, press the MFB twice quickly. To pause playback, single press the MFB again. To end the call, single press the MFB again. To answer an incoming call, single press the MFB. The headset will default to the last mode it was set to when turned off. Quick press the power button to enter Bluetooth mode and enable both phone calls and Bluetooth audio (such as when listening to music). Note when the headset is in RF wireless mode and paired via Bluetooth with a mobile phone, it will only accept and receive phone calls. When the headset is in RF wireless mode the status LED will blink red, orange or green depending on the current battery level. Quick press the power button to toggle between RF wireless and Bluetooth modes. When the headset is paired, the status LED will blink blue. With the headset powered on, enable pairing by holding the MFB until the status LED rapid blinks red and blue. Then adjust volume with the headset volume control. Adjust volume control (Headphones) to maximum level. Use the PlayStation UI to set “Output to Headphones” to “All Audio”. PLAYSTATION - Connect the wireless USB transmitter to any USB port on your PS4 or PS5 console. After the device driver is installed, we recommend you reboot your PC before use. NOTE: The first time you use the CORSAIR HS80 MAX WIRELESS headset on a PC, the operating system will automatically install a device driver. The headset is designed to operate at a range of up to 50 feet (15.24m) from the transmitter, but other wireless devices, electronics and obstructions such as walls may impact performance. The headset powers on in RF wireless mode by default. PC - Connect the wireless USB transmitter to any USB (type-A) port on your PC. PAIRING STATUS LED (WIRELESS USB RECEIVER).BLUETOOTH / MULTI-FUNCTION BUTTON (MFB).VOLUME CONTROL / EQ SELECT / iCUE CONTROL.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |